Cornick Help Center

    ALC-PACK/WG2020 Factory Defaulting

    ALC-PACK / WG2020 alarm panel, resetting to factory settings.

    How to Restore to Manufacture Settings of WGSMS2020 systems on the list below

     

     

    This process does not delete any Sensors or Remotes, the Solar Siren (ALC-SIR2) & Internal Siren (ALC-SIR1) will be deleted. 

     

    Alarm Panel Reset Procedure


    ALC-PACK1 (G5W)

    If you have changed the SIM, its recommended to restore default settings and enter the new number.

    - Send 4x ZERO (0000) to the SIM card of G5W Panel

    OR

    1. Press & hold down tamper switch for 4 seconds and then
    2. Press it 5 times in 3 seconds.
    3. The panel will beep twice.

     

    ALC-PACK2 (AW1)

    Press and hold the [WiFi] button for 7 seconds.
    You will hear a short beep after 3 seconds and then a long beep after another 4 seconds.

    The reset has been completed and all the settings have been restored to default conditions.

    Please note that this process does not delete any Sensors.

     

    ALC-PACK3, 4 (AW1 Plus)

    Click the [WiFi] button for 3 times, then press and hold it for 3 seconds.
    A long beep indicates the reset was successful.

    All the settings have been restored to the default conditions.
    Please note that this process does not delete any Sensors.

    ALC-PACK5 (H4-LTE)

    Hold the pairing button for 10 seconds.
    The ALC-PACK5 Panel will beep twice indicating it has been successfully restored.

    Note: Previously paired accessories will remain connected to your ALC-PACK5 Panel after a restore.

    Network Reconfiguration:
    - Go to [Settings] then [More] then [Network Configuration] then [Reconfiggulation]
    - Press the WiFi configuration button on the hub 3 times, after the beep, the WiFi indicator light will alternate between red and blue. The hub is now in configuration mode.

     



    Sensor & Accessories Reset Procedure     


    ALC-SIR1 (WS-105)  

      For Clear all Accessories or Panels

    •       Press & hold down the Connect Button for 6 seconds until once beep is heard at the same time.


    ALC-SIR2 (SPS-260)

      All the paired alarm panels or accessories will be disconnected.

    •      Press and hold the learning button of this siren for 5 seconds and release the button when two beeps are heard.

    Note: The siren will beep once when "LEARN" button is pressed.



    ALC- KP1 (KP700)

    Notes:

    - After reset, the user code, admin code and other settings will restore to default

    - Except that connected RFID tags can still disarm and open electric door lock

    • Admin Code default: 123456
    • User Code default: 1234

    Reset procedure below:

    1. (admin code) [#] (beep once) 3 (beep once) [*] [0] [*] [*] (beep once)
    2. When one beep is heard & the LED indicator keeps ON for 10 seconds
    3. The RESET is successful.


    ALC-RP1 (RT-101)


    For Deleting Accessories

     

    1. Turn the switch from OFF to ON, ALC-RPT1 will beep once.
    2. Press and hold the connect button for 5 seconds under connect mode.
    3. The blue LED lights up for 2 seconds following 3 beeps and goes off. 
    4. Then the green LED keeps steady on (working mode).


     






         

    Was this article helpful?

    Send feedback

    Can’t find what you’re looking for?

    Our customer care team is here for you.

    Contact Support