Before you begin, you must know the Master User Code for the alarm panel. By default, this code is 1835.
Pre-Configured Default User Codes
The arm panel comes pre-configured with 5 user codes.
The master code is used to program user options, such as adding and removing user codes.
It is recommended to change the default codes.
| Code | Code Type |
| 1835 | Master Code (Arm/Disarm & full access to programming all the user options.) |
| 7925 | User Code (Arm/Disarm only) |
| 8462 | User Code (Arm/Disarm only) |
| 3621 | User Code (Arm/Disarm only) |
| 0528 | User Code (Arm/Disarm only) |
Adding User Codes
Press and hold * button to enter the User Menu.
| When you see: | Action |
| Master Code + * | Enter 1835* |
| Add User Code | 0* |
| New Code + * | Input the new user code. All users must have a different code. [New User Code 1] * After that a short beep will be heard to indicate the user code is added successfully. |
| New Code + * |
[New User Code 2] * ... etc. |
| New Code + * |
Press ## to exit the User Menu. |
Example: Add user codes 1037 and 8571.
[* Hold] 1835* 0* 1037* 8571* ##
Deleting Individual User Codes
Press and hold * button to enter the User Menu.
| When you see: | Action |
| Master Code + * | Enter 1835* |
| Add User Code |
2* |
| User Code + * | Input the user code to delete [User Code] * |
| User Code + * |
Press ## to exit the User Menu. |
Example: Delete user codes 1567 and 2450.
[* Hold] 1835* 2* 1567* 2450* ##Delete
Editing User Codes
Press and hold * button to enter the User Menu.
| When you see: | Action |
| Master Code + * | Enter 1835* |
| Add User Code |
1* |
| Old Code + * | Input the existing user code to change [Existing User Code] * |
| New Code + * | Input the new user code. [New User Code] * |
| User Code + * |
Press ## to exit the User Menu. |
Example: Change user code 6567 to 3721.
[* Hold] 1835* 1* 6567* 3721* ##Delete
Assign a User Code to Partitions
Press and hold * button to enter the User Menu.
| When you see: | Action |
| Master Code + * | Enter 1835* |
| Add User Code |
11* |
| Code/Slot + * | Input the existing user code to change partition options. [User Code] * |
| Partition Number + * | Enter the partition number [Partition Number] * |
| Toggle YES/NO |
Toggle between YES/NO to select the partition this user can arm. * |
| Partition Number + * | Press ## to exit the User Menu. |
Example: Allow user 6567 to arm partition 2.
[* Hold] 1835* 11* 6567* 2* [* Toggle ON] ##
Delete
Editing User Code Properties
User Code Properties Description
| Property Number | Property Type |
| 1 | Master User Code |
| 2 | Duress Code |
| 3 | Arm to Disarm Code (Maid's Code) |
| 4 | Arm Only Code |
| 5 | Disarm Only Code |
| 6 | Global Arm/Disarm Code |
| 7 | Programmable Output Code |
| 8 | Voice Dial in Enable |
Master User
When assigned to a user, this property allows the user to act as a Master User. Master User Code has full access to programming all the user options.
Duress Code
This is a special 4 (default) or 6-digit user code and should only be used in the unique situation where an intruder forces one to disarm the system "under duress". When the [DURESS CODE] is entered, the alarm panel disarms normally - however a DURESS REPORTING CODE is transmitted to the monitoring company to inform them that you have been forced to disarm the alarm by and intruder. It is advisable to choose a code that can easily be remembered by all family (or staff) members.
Arm to Disarm Code (Maid's Code)
This property may be used to limit access to the premises. A maid's code will only disarm the system if the same code was used for arming. If armed with a code other than this code, the system will view an attempt to disarm using a maid's code as an invalid entry. Any valid user code will disarm the system if it has been armed with a maid’s code.
Arm Only Code
This code will arm the partition that it is assigned. If the partition is disarmed, entering an arm code will arm the assigned partition
Disarm Only Code
This code will disarm the partition it is assigned. If the partition is armed, entering the code will disarm the assigned partition.
Global Arm/ Disarm Code
When there is more than one partition, and all are disarmed, entering a global code will arm all partitions that are ready to arm. If all partitions are armed then entering a global code will disarm all partitions. Where some partitions are armed and other partitions are disarmed then entering a global code at the keypad of an armed partition will disarm all partitions. Similarly, entering a global code at the keypad of a disarmed partition will arm all partitions, if they are ready to arm. A remote transmitter programmed with a global code will arm all disarmed partitions when the arm/disarm button is pressed, if they are ready to arm. NOTE: A partition that is not ready to arm, for instance one with a zone violation, will NOT arm with the global arm/disarm code.
Press and hold * button to enter the User Menu.
| When you see: | Action |
| Master Code + * | Enter 1835* |
| Add User Code |
10* |
| Code/Slot + * | Input the existing user code to change the properties. [User Code] * |
| Property | Enter the property number (See table in the above tab) [Property] * |
| Property |
Toggle between YES/NO to enable the function for this user. * |
| Property |
Press ## to exit the User Menu. |
Example: Set user 6567 to a Disarm Only Code.
[* Hold] 1835* 10* 6567* 5* [* Toggle ON] ##